FreeRTOS Support Archive
The FreeRTOS support forum is used to obtain active support directly from Real
Time Engineers Ltd. In return for using our top quality software and services for
free, we request you play fair and do your bit to help others too! Sign up
to receive notifications of new support topics then help where you can.
This is a read only archive of threads posted to the FreeRTOS support forum.
The archive is updated every week, so will not always contain the very latest posts.
Use these archive pages to search previous posts. Use the Live FreeRTOS Forum
link to reply to a post, or start a new support thread.
[FreeRTOS Home] [Live FreeRTOS Forum] [FAQ] [Archive Top] [August 2015 Threads] STM32F103C8T6 Bit toggling in task doesn't work?Posted by nikola1010 on August 24, 2015 Hi all,
just succedded in compilation of FreeRTOS and wanted to try simple pin toggle.
Small dev board that I got off ebay has led on PC13 (logic low active).
When I put code from task into main it works, but in task itself it does't.
Could someone provide hint on that? (thank you in advance :)
------8<--------------8<--------------8<--------------8<--------------8<--------
/* Standard includes. */
include
/* Scheduler includes. */
include "FreeRTOS.h"
include "task.h"
include "queue.h"
include "stm32f10x.h"
include "stm32f10x_rtc.h"
include "stm32f10x_gpio.h"
/* The time between cycles of the 'check' task - which depends on whether the
check task has detected an error or not. */
define mainCHECKDELAYNOERROR ( ( TickTypet ) 5000 / portTICKPERIODMS )
define mainCHECKDELAYERROR ( ( TickTypet ) 500 / portTICKPERIOD_MS )
/* Task priorities. */
define mainSEMTESTPRIORITY ( tskIDLE_PRIORITY + 1 )
define mainBLOCKQPRIORITY ( tskIDLE_PRIORITY + 2 )
define mainCHECKTASKPRIORITY ( tskIDLE_PRIORITY + 3 )
define mainFLASHTASKPRIORITY ( tskIDLE_PRIORITY + 2 )
define mainECHOTASKPRIORITY ( tskIDLE_PRIORITY + 1 )
define mainINTEGERTASKPRIORITY ( tskIDLE_PRIORITY )
define mainGENQUEUETASKPRIORITY ( tskIDLEPRIORITY )
/-----------------------------------------------------------/
/*
* Configure the hardware for the demo.
*/
static void prvSetupHardware( void );
/* The 'check' task as described at the top of this file. */
static void prvMyTask( void *pvParameters );
/-----------------------------------------------------------/
uint8_t gBITSET=0;
define mainDELAYLOOPCOUNT ( 0xffffff )
int main( void )
{
ifdef DEBUG
debug();
endif
/* Set up the clocks and memory interface. */
prvSetupHardware();
/* Create the 'check' task, which is also defined within this file. */
xTaskCreate( prvMyTask, "MyTask", configMINIMAL_STACK_SIZE, NULL, mainCHECK_TASK_PRIORITY, NULL );
/* Start the scheduler. */
vTaskStartScheduler();
/* Will only get here if there was insufficient memory to create the idle
task. The idle task is created within vTaskStartScheduler(). */
for( ;; );
}
/-----------------------------------------------------------/
static void prvCheckTask( void *pvParameters )
{
for( ;; )
{
for( ul = 0; ul < mainDELAY_LOOP_COUNT; ul++ ) // PAUSE
{}
GPIO_WriteBit(GPIOC , GPIO_Pin_13 , Bit_RESET);
for( ul = 0; ul < mainDELAY_LOOP_COUNT; ul++ ) // PAUSE
{}
GPIO_WriteBit(GPIOC , GPIO_Pin_13 , Bit_SET);
}
}
/-----------------------------------------------------------/
static void prvSetupHardware( void )
{
/* RCC system reset(for debug purpose). */
RCC_DeInit ();
/* Enable HSE. */
RCC_HSEConfig( RCC_HSE_ON );
/* Wait till HSE is ready. */
while (RCC_GetFlagStatus(RCC_FLAG_HSERDY) == RESET);
/* HCLK = SYSCLK. */
RCC_HCLKConfig( RCC_SYSCLK_Div1 );
/* PCLK2 = HCLK. */
RCC_PCLK2Config( RCC_HCLK_Div1 );
/* PCLK1 = HCLK/2. */
RCC_PCLK1Config( RCC_HCLK_Div2 );
/* ADCCLK = PCLK2/4. */
RCC_ADCCLKConfig( RCC_PCLK2_Div4 );
/* Flash 2 wait state. */
*( volatile unsigned long * )0x40022000 = 0x01;
/* PLLCLK = 8MHz * 9 = 72 MHz */
RCC_PLLConfig( RCC_PLLSource_HSE_Div1, RCC_PLLMul_9 );
/* Enable PLL. */
RCC_PLLCmd( ENABLE );
/* Wait till PLL is ready. */
while (RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET);
/* Select PLL as system clock source. */
RCC_SYSCLKConfig (RCC_SYSCLKSource_PLLCLK);
/* Wait till PLL is used as system clock source. */
while (RCC_GetSYSCLKSource() != 0x08);
/* Enable GPIOA, GPIOB, GPIOC, GPIOD, GPIOE and AFIO clocks */
RCC_APB2PeriphClockCmd( RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB |RCC_APB2Periph_GPIOC
| RCC_APB2Periph_GPIOD | RCC_APB2Periph_GPIOE | RCC_APB2Periph_AFIO, ENABLE );
/* Set the Vector Table base address at 0x08000000. */
NVIC_SetVectorTable( NVIC_VectTab_FLASH, 0x0 );
NVIC_PriorityGroupConfig( NVIC_PriorityGroup_4 );
/* Configure HCLK clock as SysTick clock source. */
SysTick_CLKSourceConfig( SysTick_CLKSource_HCLK );
/* SPI2 Periph clock enable */
RCC_APB1PeriphClockCmd( RCC_APB1Periph_SPI2, ENABLE );
/**************************************/
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE);
GPIO_StructInit(&GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_13;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOC, &GPIO_InitStructure);
GPIO_WriteBit(GPIOC , GPIO_Pin_13 , Bit_SET);
}
/-----------------------------------------------------------/
void vApplicationStackOverflowHook( TaskHandle_t pxTask, char pcTaskName )
{
/ This function will get called if a task overflows its stack. If the
parameters are corrupt then inspect pxCurrentTCB to find which was the
offending task. */
( void ) pxTask;
( void ) pcTaskName;
for( ;; );
}
/-----------------------------------------------------------/
void assert_failed( unsigned char *pucFile, unsigned long ulLine )
{
( void ) pucFile;
( void ) ulLine;
for( ;; );
}
STM32F103C8T6 Bit toggling in task doesn't work?Posted by nikola1010 on August 25, 2015
STM32F103C8T6 Bit toggling in task doesn't work?Posted by rtel on August 26, 2015 You only appear to be creating one task, which is implemented by prvMyTask(), but you don't show the code for that task.
Copyright (C) Amazon Web Services, Inc. or its affiliates. All rights reserved.
|