Quality RTOS & Embedded Software

 Real time embedded FreeRTOS RSS feed 
Quick Start Supported MCUs PDF Books Trace Tools Ecosystem


xTaskCheckForTimeOut()
[Task Utilities]

task.h
BaseType_t xTaskCheckForTimeOut( TimeOut_t * const pxTimeOut,
                                 TickType_t * const pxTicksToWait );

This function is intended for advanced users only.

A task can enter the Blocked state to wait for an event. Typically, the task will not wait in the Blocked state indefinitely, but instead a timeout period will be specified. The task will be removed from the Blocked state if the timeout period expires before the event the task is waiting for occurs.

If a task enters and exits the Blocked state more than once while it is waiting for the event to occur then the timeout used each time the task enters the Blocked state must be adjusted to ensure the total of all the time spent in the Blocked state does not exceed the originally specified timeout period. xTaskCheckForTimeOut() performs the adjustment, taking into account occasional occurrences such as tick count overflows, which would otherwise make a manual adjustment prone to error.

xTaskCheckForTimeOut() is used with vTaskSetTimeOutState(). vTaskSetTimeOutState() is called to set the initial condition, after which xTaskCheckForTimeOut() can be called to check for a timeout condition, and adjust the remaining block time if a timeout has not occurred.

Parameters:
pxTimeOut   A pointer to a structure that holds information necessary to determine if a timeout has occurred. pxTimeOut is initialized using vTaskSetTimeOutState().
pxTicksToWait   Used to pass out an adjusted block time, which is the block time that remains after taking into account the time already spent in the Blocked state.
Returns:
If pdTRUE is returned then no block time remains, and a timeout has occurred.

If pdFALSE is returned then some block time remains, so a timeout has not occurred.

Example usage:

/* Driver library function used to receive uxWantedBytes from an Rx buffer that
is filled by a UART interrupt.  If there are not enough bytes in the Rx buffer
then the task enters the Blocked state until it is notified that more data has
been placed into the buffer.  If there is still not enough data then the task
re-enters the Blocked state, and xTaskCheckForTimeOut() is used to re-calculate
the Block time to ensure the total amount of time spent in the Blocked state does
not exceed MAX_TIME_TO_WAIT. This continues until either the buffer contains at
least uxWantedBytes bytes, or the total amount of time spent in the Blocked state
reaches MAX_TIME_TO_WAIT – at which point the task reads however many bytes are
available up to a maximum of uxWantedBytes. */
size_t xUART_Receive( uint8_t *pucBuffer, size_t uxWantedBytes )
{
size_t uxReceived = 0;
TickType_t xTicksToWait = MAX_TIME_TO_WAIT;
TimeOut_t xTimeOut;

   /* Initialize xTimeOut.  This records the time at which this function was
   entered. */
   vTaskSetTimeOutState( &xTimeOut );

   /* Loop until the buffer contains the wanted number of bytes, or a timeout
   occurs. */
   while( UART_bytes_in_rx_buffer( pxUARTInstance ) < uxWantedBytes )
   {
      /* The buffer didn't contain enough data so this task is going to
      enter the Blocked state.  Adjusting xTicksToWait to account for any time
      that has been spent in the Blocked state within this function so far to
      ensure the total amount of time spent in the Blocked state does not exceed
      MAX_TIME_TO_WAIT. */
      if( xTaskCheckForTimeOut( &xTimeOut, &xTicksToWait ) != pdFALSE )
      {
         /* Timed out before the wanted number of bytes were available, exit the
         loop. */
         break;
      }

      /* Wait for a maximum of xTicksToWait ticks to be notified that the receive
      interrupt has placed more data into the buffer. */
      ulTaskNotifyTake( pdTRUE, xTicksToWait );
   }

   /* Attempt to read uxWantedBytes from the receive buffer into pucBuffer.  The
   actual number of bytes read (which might be less than uxWantedBytes) is
   returned. */
   uxReceived = UART_read_from_receive_buffer( pxUARTInstance,
                                               pucBuffer,
                                               uxWantedBytes );

   return uxReceived;
}






[ Back to the top ]    [ About FreeRTOS ]    [ Privacy ]    [ Sitemap ]    [ ]


Copyright (C) Amazon Web Services, Inc. or its affiliates. All rights reserved.

Latest News

NXP tweet showing LPC5500 (ARMv8-M Cortex-M33) running FreeRTOS.

Meet Richard Barry and learn about running FreeRTOS on RISC-V at FOSDEM 2019

Version 10.1.1 of the FreeRTOS kernel is available for immediate download. MIT licensed.

View a recording of the "OTA Update Security and Reliability" webinar, presented by TI and AWS.


Careers

FreeRTOS and other embedded software careers at AWS.



FreeRTOS Partners

ARM Connected RTOS partner for all ARM microcontroller cores

Espressif ESP32

IAR Partner

Microchip Premier RTOS Partner

RTOS partner of NXP for all NXP ARM microcontrollers

Renesas

STMicro RTOS partner supporting ARM7, ARM Cortex-M3, ARM Cortex-M4 and ARM Cortex-M0

Texas Instruments MCU Developer Network RTOS partner for ARM and MSP430 microcontrollers

OpenRTOS and SafeRTOS

Xilinx Microblaze and Zynq partner